Filter By:

  • Show More Brands
  • Show Fewer Brands
  • Show More Sizes
  • Show Fewer Sizes

Accessories

bicycle supplies 

Bicycle accessories & tools for sale.

Ride prepared for any situation.


eBikeKit Budget 36v 12ah SLA kit w/charger
$399.99
Economical battery pack for e-bikes and e-trikes. 3X12v12ah SLA batteries and charger, wiring, fuse, switch and bag. 250 cycles, 10-15 miles. Installation extra. Specifications subject to change.
eBikeKit Budget Front wheel electric trike kit
$399.99
Front: 20/24/26" 500w, 36v, throttle only, no battery (specifications are subject to change - installation is extra) Powerful 500w/750W 36V brushless hub motor that allows up to 25 KM/H top speed The kit includes motorized wheel (not inculdes the tire), motor controller, speed throttle, power break lever, wire harness Drive system has no moving chains or gears, no friction, more efficient, less chance to break! Brake shuts off motor automatically, saves energy, improves safety! Thumb throttle only - with 3 LEDs indicator lights
eBikeKit HD Front wheel e-Trike Conversion Kit
$699.99
E-TrikeKit™ Adult Tricycle Conversion Kit 20" 24" or 26" with Heavy-Duty (Low Speed / High Torque) 500w Direct-Drive Hub Motor (specifications are subject to change - installation extra) The E-TrikeKit electric tricycle conversion kit without battery pack is specifically made with increased pulling power for heavier adult tricycles. The direct-drive hub motor is designed to deliver more low-end torque and a lower top speed; important for safety on a 3-wheeler. This kit without battery gives you the option of supplying your own 36 or 48 volt battery pack. The E-TrikeKit is also available in a single rear wheel by request for special applications; supplies are limited. Who's it for? This kit is built specifically for upright adult tricycles. The heavy-duty direct-drive motor is designed for increased torque and a lower top speed. This kit also has speed-limited reverse (30% of forward top speed). The E-TrikeKit™ is designed specifically for adult tricycles. Upgraded in 2015 to include our LCD dashboard display, 36v/48v 12FET controller, speed-limited reverse function, and locking e-brake handles, the system is easy to install and operate and gives the rider total control over top speeds and power output. This trike specific conversion kit allows you to turn any conventional 3-wheel adult tricycle into an electric-assisted adult mobility tricycle. Conversion Kit Specs: Watts (Nominal/Peak): 500-1000w (EBK 22amp controller) Top Speed: Approx. 14 MPH @36v in 26" wheel & 20 MPH @48v in 26" wheel (add this kit and any 48v battery to cart separately for this combination) Range: Depends on battery capacity(AH), total load, rider input and terrain Performance: Medium Efficiency: Low Stealth Factor: Low
Zipp QuickView Road Low Computer Mount
$22.00
Low Road position places the computer in front of the bar and nearly flush with the top of the bar, making for an easy to read display whether you are on the hoods or in the drops. - Sub-20 gram computer mount - Compatible with computers with 1/4 turn twist lock interface and 31.8mm bar surface - Single Torx T25 fixing bolt
Willworx Superstand Bike Stand
$43.90 - $52.99
- Shop quality bicycle display and storage stand - Graphite ripple powdercoat over steel construction - Four-Point, Foam rubber end-Cap feet - 2 Piece design disassembles for space-Efficient storage - Standard and extreme models feature welded base construction (Extreme model accepts up to 3 inch tires) - Retail model features flat-Packed, Bolt-Together base construction - Fat rack features flat-Packed, Bolt-Together base construction and will suit tires from 3.8" To 5" with three width positions, 4.25", 4.75" And 5.25"
White Lightning Clean Streak
$9.79 - $19.99
Clean Streak, Shop Size, 23oz Aerosol - Evaporates fast and leaves no residue - A "no-scrub" cleaner that cleans to the base and prepares surfaces for application of high performance lubricants - No water rinsing is required - Clean Streak's No-Rinse, No-Residue formula is perfect for use on disc brake rotors
Wheels Manufacturing Inc. 29mm SRAM DUB Open Bore Adapter
$8.00
This 29mm open bore adapter is used to press 29mm x 42mm (DUB) sealed bearings. The adapter is machined with one step at 29mm OD, which fits into the center of the sealed bearing. For use with Wheels Mfg. bottom bracket press (PRESS-7 , PRESS-7-PRO or PRESS-9-PRO). - Inner step outer diameter: 28.9mm - Outer diameter: 41.8mm - Thru hole diameter: 12.8mm (1/2-inch) - Thickness: 7mm - Machined, red anodized aluminum - Sold individually
Wheels Manufacturing Inc. Universal Bottom Bracket Drift
$15.00
The Wheels Manufacturing universal bottom bracket drift presses all current Wheels Mfg bottom bracket cups into your frame or bearing cups. The adapter is machined with multiple steps to fit common bottom bracket shell and bearing diameters listed below. Each step is laser etched with the diameter size. - Inner hole sized to fit 1/2" threaded rod. Not for use with Wheels Mfg PRESS-1 or PRESS-4 - Compatible with any other press with a 1/2" diameter rod - Recommended for use with Wheels Mfg Universal BB Press - Machined aluminum - Anodized Red - Sold individually - Drift can also be used as a frame bottom bracket shell sizing guide! Fits the following bottom bracket shell sizes: - BB30 (42mm) - PF30 (46mm) - BB86, BB92 (41mm) - BBRight (46mm) - BB386EVO (46mm) - Cannondale BB30A (42mm) - Cannondale PF30A (46mm) - Specialized Carbon OSBB (46mm) - Specialized Alloy OSBB (42mm) - TREK BB90, BB95 (37mm) - PF24 (41mm)
Wheels Manufacturing Inc. Double End BB Wrench
$23.50
This Wheels Mfg. Double End Bottom Bracket wrench fits 16-notch bearing cups with an outside diameter of 44mm as well as 16-notch bearing cups with an outside diameter of 48.5mm. - Machined aluminum - Anodized red. - Compatible with all current Wheels Mfg bottom brackets with notched cups
Wheels Manufacturing Inc. Economy Bearing Press
$39.00
An indispensable tool for the serious amateur bike mechanic or smaller bike shop, the Wheels Manufacturing Bearing Press is designed for installation of bottom brackets or sealed bearings with a minimum I.D. of 10mm. - Package includes 2 handles and a 3/8"-12 threaded rod - Economy Bearing Press, used with separately-purchased bearing adaptors
Wheels Manufacturing Inc. Universal Bottom Bracket Press
$45.00
This do-it-all universal bottom bracket press is designed to press in all current Wheels Mfg. bottom brackets. Economical and easy to use, this tool is made up of two machined aluminum handles, a 1/2-inch threaded rod, and two machined aluminum drifts. Each drift is machined with multiple steps to fit common bottom bracket shell and bearing diameters. No more searching for the correct size drifts and parts—just match up the drift to your frame's BB shell size and your bottom bracket's bearing size, and press away. - Zinc-plated 1/2-inch diameter threaded rod resists bending, allowing for the cups to align and press in straight - Drifts can also can be used as a frame bottom bracket shell sizing guide - Machined aluminum handles and drifts - Red anodized drifts and handles - Steps on drift are marked with diameter sizes - Works with BB shells up to 132mm wide - Includes two universal BB drifts
Wheels Manufacturing Inc. Bottom Bracket Socket
$49.00
Use this double-sided socket tool for installing and removing both 48.5mm and 44mm 16-notch bottom bracket cups. Socket is machined for 1/2-inch drive, but a 3/8-inch to 1/2-inch adapter is included so you can use it with 3/8-inch drive torque wrenches. - Compatible with all Wheels Manufacturing bottom brackets that have 48.5mm or 44mm, 16-notch spline patterns - Also compatible with FSA MegaEVO BB cups, Shimano, SRAM/Truvativ, Campagnolo Ultra Torque, and FSA - Machined 6061 aluminum - Anodized red
Wheels Manufacturing Inc. Dropout Saver Kit
$60.00
The dropout saver system is an alternative to replacing badly bent or damaged derailleur dropouts. Rather than replacing the damaged dropout completely, simply drill out the damaged threads, install a dropout saver, and realign the dropout. Kit includes: - (1) 15/32-inch reduced shank drill bit - (2) DS-1 wide dropout savers     - (3) DS-2 narrow dropout savers    
Wheels Manufacturing Inc. Hub Bearing Installation Drift Set
$84.00
This 23-piece Wheels Mfg. drift set is used to install 10mm and larger inside diameter sealed bearings, using a press with 3/8" diameter rod - Includes open bore and over axle drifts for 6802, 6901, 6902, 6903, 6000, and 6001 bearings - 10mm ID hole, for use with Wheels Manufacturing PRESS-1 or PRESS-4 bearing press handles
Wheels Manufacturing Inc. Bottom Bracket Sealed Bearing Extractor Set
$99.00
- Bearing extractors set for pushing out 22mm, 24mm, and 30mm ID sealed bearings from bottom bracket cups. - Compatible with Wheels Mfg. 1/2" threaded rod press and handles (PRESS-7 and PRESS-7-PRO). BB-EXT Includes (1) 30mm ID sealed bearing extractor (1) 24mm ID sealed bearing extractor (1) 22mm ID sealed bearing extractor (1) 52mm receiver cup (1) 44mm receiver cup sleeve (1) 42mm receiver cup sleeve (1) 39mm receiver cup sleeve (1) bearing pusher shaft
Wheels Manufacturing Inc. Headset Cup Press
$125.00
Wheels Mfg Headset Cup Press is a robust, and easy to use tool made up of two machined aluminum handles, 1/2" threaded rod, and two machined aluminum drifts. One drift is machined with multiple steps to fit common head tube inner diameters. The other drift is two-sided to press in cups with either 1-1/8" or 1-1/2" bearings, but may be used for other cups with odd sized sealed bearings. - Machined aluminum handles and drifts - Red anodized drifts and handles - Zinc-plated 1/2" diameter threaded rod - Long threaded rod works with long head tubes up to 250mm - Includes one Head Tube Drift - Includes one Headset Cup Drift - Laser etched for easy identification - Made in the USA
Wheels Manufacturing Inc. Sealed Bearing Extractor Set
$240.00
This Wheels Manufacturing Sealed Bearing Extractor Set removes sealed bearings with an inside diameter of 8mm to 30mm. Insert the extractor into the bearing, tighten one side with an Allen key, and the collet expands to grip the inside of the bearing. Tap the extractor out with a punch. - 12-piece set (Individual replacement extractors and parts are also available) - Made in the USA Set includes: - (1) Clear Plastic storage container - (1) 8mm ID Bearing Extractor - (1) 9mm ID Bearing Extractor - (1) 9.5mm ID Bearing Extractor - (1) 10mm ID Bearing Extractor - (1) 12mm ID Bearing Extractor - (1) 15mm ID Bearing Extractor - (1) 17mm ID Bearing Extractor - (1) 20mm ID Bearing Extractor - (1) 22mm ID Bearing Extractor - (1) 24mm ID Bearing Extractor - (1) 25mm ID Bearing Extractor - (1) 30mm ID Bearing Extractor - (1) Spare parts bag containing bolt sets for extractors
Wheels Manufacturing Inc. Professional Bottom Bracket Tool Kit
$250.00
This is Wheels Manufacturing's new toolkit for installing, removing, and servicing Wheels Manufacturing bottom brackets. The kit includes their new bottom bracket socket tools for installing and removing Wheels Mfg. BB cups with the following spline patterns: 48.5mm 16-notch, 44mm 16-notch (may be compatible with FSA MegaEVO BB cups, Shimano, SRAM/Truvativ and FSA). It also includes sealed bearing extractors for 22mm, 24mm, and 30mm ID bearings. Includes - T-Handles with 1/2" threaded rod - (2) Universal bottom bracket drift (BB-OB) - (1) 48.5mm/44mm, 16-notch Bottom Bracket Socket - (1) 48.5mm, 16-notch Single Sided BB Socket - (1) 30mm ID sealed bearing extractor - (1) 24mm ID sealed bearing extractor - (1) 22mm ID sealed bearing extractor - (1) receiver cup - (1) 44mm receiver cup sleeve - (1) 42mm receiver cup sleeve - (1) 39mm receiver cup sleeve - (1) bearing pusher shaft - (1) 3/8" to 1/2" square drive adapter - Wood base
Wheels Manufacturing Inc. Sealed Bearing Press
$325.00
- Installs 16 bearing sizes including 3 different bottom bracket bearings: 2437, 6000, 6001, 6002, 6003, 6801, 6802, 6803, 6804, 6805, 6806, 6900, 6901, 6902, 6903, 6904 - Includes T-handles with Acme threaded rods, wood base with dowels for holding adapters, 16 bearing installation drifts, 3 "speed spacers" and 2 linkage offsets for full suspension bearing installation - Made in the USA
Wald 137 Front Basket
$19.99 - $20.99
The 157's little brother, this basket is just as functional. Some people don't need to cart around large pizzas or multiple full size grocery bags, so this basket is for the more streamlined commuters and delivery pros. Sturdy one-piece legs offer all the support you'll need when hauling heavier loads. - Fits most bikes - Adjustable legs mount to front axle for a secure fit - 15" x 10" x 5" deep - Easy to install
Wald 151 Drop Top Front Basket
$23.99
- A unique blend of functionality and style - Offers the convenience of carrying your gear within easy reach of the handlebar - The only basket in Wald's lineup that offers lowered front and side wires for just a touch of unique appeal - Hardware included - UV and weather resistant - 14" x 9" x 7"
Wald 135 Grocery Front Basket
$24.99 - $29.99
We know you love the 133, 3133, and 157 baskets. But what happens when you want to haul something that isn't overly large, but can really weigh you down? We thought you'd probably bust out a welding torch and tack a couple of legs on the 133 basket. So that's exactly what we did. The 135 is the exact same size as our popular 133 and 3133 baskets with shorter handlebar mounts and legs bolted to the bottom of the basket. Perfect for a couple of two liters, or a six-pack with some chips and salsa to go. - Basket dimensions: 14.5 X 9.5 X 9 inches - Legs match the finish of the basket - Same size as the popular 133 and 3133 baskets with shorter handlebar mounts
Wald 139 Front Basket
$24.99 - $29.99
The 157's little brother, this basket is just as functional. Some people don't need to cart around large pizzas or multiple full-size grocery bags, so this basket is for the more streamlined commuters and delivery pros. Sturdy one-piece legs offer all the support you'll need when hauling heavier loads. This rack cannot be used on bicycles with front suspension systems or springer forks. - Standard front bicycle basket fits most bikes - Adjustable legs mount to front axle for a secure fit - 18" x 13" x 6" deep - UV Weather-resistant bike basket - Available with wooden bottom to better hold your cargo
Wald 1352 Front Grocery Basket with Adjustable Legs
$26.18
A verstile basket that can manage anything from books to groceries. - Extended handlebar clamps allow greater clearance for shift and brake cables - Legs extend from approx. 14" to 22" when mounted to the axle or eyelets - Fits 7/8" to 31.8mm handlebars - Made in USA - Dimensions: 14 x 9 x 9"
Wald 124 Compact Front Basket
$27.58
- Polyester powder coating - Bolt-on legs stabilize heavy loads - Hardware included - 11.75" x 8" x 9"
Wald 3114 Front Lift-Off Basket
$28.99 - $29.99
This front basket system uses a bolt-on handlebar mount to allow for quick and easy removal of the basket itself. - Extended handlebar clamps allow greater clearance for shift and brake cables - Requires 3.5" of handlebar clearance for mount - Fits 7/8" to 31.8mm handlebars - Made in USA - Dimensions: 11.75 x 8 x 9"
Wald 114 Front Lift-Off Basket
$29.99
- Includes basket holder - Carrying handle for off bike use - Polyester powder coating - 11.75" x 8" x 9"
Wald Wald Training Wheels 1216
$29.99
Wald's 1216 training wheels are designed to mount on most single speed bicycles with 12- to 16-inch wheels. This model is intended for use by riders weighing up to 75 pounds.
Wald 198 Multi-Fit Basket
$34.99
This versatile basket is the most adaptable front basket Wald offers. - Made in U.S.A. (Maysville, KY) - Deep basket that is sized for a grocery sack - Dimensions: 14.5 x 9.5 x 9 inches; basket tapers to 12.25 x 7 inches - Extended handlebar clamps fit 7/8" and 1" diameter handlebars - Two-piece adjustable legs extend from approx. 14 inches to 22 inches and mount to either the front axle or fork eyelets for bikes with quick release front hubs - Available in gloss black (198GB) or white (198WH) Powder Coat Finish - Complete basket weighs 3 lbs.
Wald Middleweight 952 Fender Set
$38.99
These steel fenders offer tire coverage that is durable with a timeless aesthetic. - The crescent full-coverage design offers a closer fit around the tire - Made in the USA
Page 1 of 62 Next page
Subscribe