Filter By:

  • Show More Brands
  • Show Fewer Brands

Gas Bikes

Micargi Bare Bones gas bike

Gas Bike Conversions Fully Built and Ready To Ride.

Fully built bikes in stock. Or, we can build your bike from your specifications. 4-stroke and 2-stroke kits. Call to setup a custom build: 480-275-5818. We can build your bike, test and run it, drain it, pack it up, and ship it to you. We do repairs and will finish your build if you get stuck. Get repairs on any bike. Pickup & Delivery available too. Need more information about the law on Gas Bike operation? Go to: Gas Bike FAQs

Important Gas Bike information

  • All gas bikes shown are assembled from kits
  • All guarantees are solely from manufacturer
  • All gas bikes are sold as-is
  • These kits are not approved for use on public highways (lanes of traffic)
  • Gas Bikes are not titled and are unregistered and are not motor vehicles
  • Gas bike kits and conversions are essentially toys (your hobby)
  • Customer accepts all risks of use
  • Operating a bike, motorized bicycle or bike with a bicycle engine installed involves some risk of serious bodily injury. Buyer accepts responsibility for any and all vehicle operation that may lead to personal injury, economic loss, social distress, other losses, costs and damages.
  • Seller is not responsible for injuries and/or damages resulting from operating this motorized bicycle or bicycle engine
  • Seller is not responsible for misuse of this or any warranty
  • Not all motorized bicycles are allowed for bike lane use - check your local laws
  • We make no guarantee as to the road legality of these bike kits
  • Check your bike for safety before evey ride
  • Pedal when starting out to save wear on the clutch
  • Wear a helmet
  • See our terms and conditions

NOTE: Our gasoline operated products are NOT compliant with Environmental Protection Agency ( E.P.A. ) or California Air Resources Board (C.A.R.B) for the use on/off Public roads. 


BBR Deluxe Fully Assembled gas bike kit
Gas Bike Kit - Fully Assembled - call us to make your custom order: 1-480-275-5818 We build the bike, run and ride it, drain and box it up for shipping. You get a ready-built bike that has been fully tested. 49cc 4-stroke engine approximately 2.5 HP this bicycle engine gets about 100 to 150 mpg and can hits speeds of 35 MPH or more. 4 cycle engines require little maintenance. Simply add gas and oil and the engine is ready to operate. Make regular oil changes and your engine will last you for many years to come. this trim package comes with pull start and auto clutch. 48cc and 66/80cc engines have similar horsepower, but a very narrow power band. You must mix your gas and oil to run the engine. You can get up to 150 miles per tank and reach speeds up to 30mph. Two-strokes are a bit messy and a little noisy, but fun to ride and easy to service. This trim package comes with a manual clutch and pedal start. This bike is built on a custom 19.5, med-lg, aluminum gas bike frame with built-in 2.4l gas tank. It has mag Wheels front and rear for no broken spokes. The automatic centrifugal clutch works smooth and convenient. Front forks are triple-tree type and add strength as well as a smoother ride. 26X2.0 highway/MTB tires round out the package. This bike is fast, so be warned. Large (5'6" to 6'4"), lightweight aluminum, Gas Bike Frame Single Speed rear freewheel Front Disc Brake option on triple-tree fork or MTB fork shown Notice and Disclaimer on Gas Bikes All gas bikes shown are assembled from kits. All guarantees are solely from manufacturer. All gas bikes are sold as-is. These kits are not approved for use on public highways, but may be permitted along the side of the road. Always follow all laws of operation for the jurisdiction you are riding. Gas Bikes are not titled and are unregistered and are not motorized vehicles. Gas bike kits and conversions are essentially toys (your hobby). Customer accepts all risks of use. Operating a bike, motorized bicycle or bike with a bicycle engine installed involves some risk of serious bodily injury. Buyer accepts responsibility for any and all vehicle operation that may lead to personal injury, economic loss, social distress, other losses, costs and damages. Seller is not responsible for injuries and/or damages resulting from operating this motorized bicycle or bicycle engine. Seller is not responsible for misuse of this or any warranty. Not all motorized bicycles are allowed for operation on roads, bike lanes or the side of the road. We make no guarantee as to the road legality of these bikes. See our terms and conditions on your sales invoice. Our gasoline operated products are NOT compliant with Environmental Protection Agency ( E.P.A. ) or California Air Resources Board (C.A.R.B) for the use on/off Public roads. Upon purchase, the buyer agrees to use products for racing (closed-course competition) only. Check your bike for safety before every ride. Wear a helmet. Pedal when starting out to save wear on the clutch. Other gas bike models are available. Delivery and shipping options.
Micargi Cruiser Gas Bike Conversion 2 Stroke 80cc Gas Bike
Single Speed Beach Cruiser 26" Wheels 80cc flying horse 2 Stroke Motor Coaster brake Notice and Disclaimer on Gas Bikes All gas bikes shown are assembled from kits. All guarantees are solely from manufacturer. All gas bikes are sold as-is. These kits are not approved for use on public highways, but may be permitted along the side of the road. Always follow all laws of operation for the jurisdiction you are riding. Gas Bikes are not titled and are unregistered and are not motorized vehicles. Gas bike kits and conversions are essentially toys (your hobby). Customer accepts all risks of use. Operating a bike, motorized bicycle or bike with a bicycle engine installed involves some risk of serious bodily injury. Buyer accepts responsibility for any and all vehicle operation that may lead to personal injury, economic loss, social distress, other losses, costs and damages. Seller is not responsible for injuries and/or damages resulting from operating this motorized bicycle or bicycle engine. Seller is not responsible for misuse of this or any warranty. Not all motorized bicycles are allowed for operation on roads, bike lanes or the side of the road. We make no guarantee as to the road legality of these bikes. See our terms and conditions on your sales invoice. Our gasoline operated products are NOT compliant with Environmental Protection Agency ( E.P.A. ) or California Air Resources Board (C.A.R.B) for the use on/off Public roads. Upon purchase, the buyer agrees to use products for racing (closed-course competition) only. Check your bike for safety before every ride. Wear a helmet. Pedal when starting out to save wear on the clutch. Other gas bike models are available. Delivery and shipping options.
KMC 415H Master Link For Gas Bike
$4.99
KMC 3/16" Master Link Chain Links - For 3/16" chain, extra wide - Extra-wide, for non-derailleur bikes: BMX, cruisers, etc - Perfectly fits on KMC 415H & 415H-NP chains
BBR Gas Bike Parts & Supplies
$9.99
Find a very large selection of new and used gas bike parts and tools. We carry most supplies you need to get back on the road fast. Service and repairs available for all brands or builds. We have small parts, tools, tires, forks, brakes, oil, chains, HD wheels, and full kits, including frames.
Sunlite Alloy Double Mountain Lever
$16.99
•Designed for cantilever & caliper brakes •22.2mm (7/8") clamp •Forged alloy construction •3 finger •Pulls two brake cables with one lever •136g each
KMC HD Chain for BMX or 415 Gas Bikes
$19.99
Important Note: BE CAREFUL. THESE ARE NOT 1/2 X 3/32 CHAIN. THEY ARE 1/2 X 3/16 CHAIN FOR HEAVY DUTY FREESTYLE/BMX USE. All KMC chains include either a missing link or replacement pins Speeds: 1sp Size: 1/2x3/16 Links: 98L Material: DB/HD Color: Black/Silver Weight: 661g (Other chains are available, up to 110 links.) These chains may not fit on some BMX due to clearance, such as 9-tooth sprockets.
KMC 415H-NP Chain For Gas Bike or BMX
$24.99
- 1/2" x 3/16” - 98 Links - Bushing Construction - Full Nickel Plated - Heavy Duty Structure - Width: 13.1 mm - Drivetrain Speeds: Single Speed 1/2" x 3/16" - Chain Connection Type: Reusable Master Link - Half Link Chain: No - Weight: 800g
Wheel Master 26
$39.99
This is a perfect choice for the heavier rider or for a gas bike. Strong 12 gauge spokes and steel hoop are a great match. Size: 26in Ft / Rr / St: FT Width ID (mm): 28 Axle: B/O 3/8 Rim Color: CP Rim Model: W/M Steel 2.125 Hub Model: W/M SB-1000 O.L.D.: 100 Hub Color: CP Brake Type: RIM Spoke Type: 12G HD UCP Spoke Count: 36H Wall: Sgl Valve: SV Type: Tube Only ISO: 559 Search Color: Chrome REPORT INCORRECT PRODUCT INFORMATION
Wheel Master 26
$44.99
Coaster brake (CB) models include trim kits Internally geared hubs include shifters unless noted otherwise Size: 26in Ft / Rr / St: RR Width ID (mm): 28 Axle: B/O 3/8 Rim Color: CP Rim Model: W/M Steel 2.125 Hub Model: W/M SB-1000 O.L.D.: 135 Hub Color: CP Gears: 5/6/7s FW Brake Type: RIM Spoke Type: 12G HD UCP Spoke Count: 36H Wall: Sgl Valve: SV Type: Tube Only ISO: 559 Search Color: Chrome
Clarks Mechanical Disc Brake Kit CMD-11 160mm
$49.99
Excellent choice to upgrade your compatible fork and wheel to a disc brake. Aluminum construction Full ball bearing action Includes caliper and mounting hardware Compatible with linear pull/mech disc brake levers Black housing Shimano Equivalent BR-M375 Front/Rear: Frt or Rr Rotor Size: 160mm Color: Black Brake Type: Mechanical Caliper Mount: Standard Post Mount
Wheel Master 26
$49.99
Heavy-duty steel coaster brake wheel with 12 gauge spokes. A perfect choice for heavy riders or gas powered bikes. Coaster brake (CB) models include trim kits Internally geared hubs include shifters unless noted otherwise Size: 26in Ft / Rr / St: RR Width ID (mm): 28 Axle: B/O 3/8 Rim Color: CP Rim Model: W/M Steel 2.125 Hub Model: KT Steel O.L.D.: 110 Hub Color: CP Gears: 1s Brake Type: CB Spoke Type: 12G HD UCP Spoke Count: 36H Wall: Sgl Valve: SV Type: Tube Only ISO: 559 Search Color: Chrome
BBR BBR Tuning Reed Valve Kit
$59.99
The BBR Tuning Reed Valve Kit will have your 66/80cc or 48cc 2-stroke engine running like a top! This reed valve kit works with our Flying Horse and Mega Motors 66cc and 48cc engines, as well as most Chinese engine kits on the market. Installation is a breeze: simply replace your existing intake manifold with the reed valve assembly, attach your carburetor to the reed's intake port, and you're done. Get an increase in bottom end torque as a smoother running throttle response with the BBR Tuning Reed Valve Kit! Fits on 40mm Intake Manifold ports - standard on 66/80 motors
BBR Expansion Chamber Thrust Muffler
$89.99
perfect for giving your motorized bike more power and that awesome throaty sound, the BBR Tuning High-Performance F2 Thrust Exhaust Muffler is what you need for optimum torque and speed out of your 2-stroke engine. Its baffle-less design uses an expansion chamber to circulate the exhaust around and out of the muffler for a smoother ride, while a long pipe lets you expel exhaust faster and more efficiently. This results in increased torque and higher top speeds. With 40mm mounting stud spacing, this muffler is compatible with nearly any 66/80cc 2 stroke engine around. So when the exhaust from your motorized bicycle engine kit is holding you back and performance mufflers aren't giving you maximum power, this High-Performance F2 Thrust Exhaust Muffler will have you screaming down the track. The BBR Tuning High-Performance F2 Thrust Exhaust Muffler is perfect for giving you more power and sound out of your 2-stroke motor. Made for racing and performance engines, you can forget that old exhaust you’re using and replace it with the Thrust muffler for better power and speed. Instead of using a baffle that will hinder your performance, the BBR Tuning F2 Thurst muffler makes use of its baffle-less design to expel more exhaust from your motor. This exhaust utilizes expansion chamber technology to circulate the exhaust around the chamber and out of the muffler for a smoother ride. Its length will also let you expel exhaust faster and more efficiently, just like a stretched or long-shot muffler would. If you’re tired of your expansion chamber always hitting your pedals or your stretch muffler hangs too low for your taste, the BBR Tuning High-Performance Thrust Exhaust Muffler is what you need. The Thrust exhaust combines the exhaust capabilities of a long shot muffler, the smoothness of an expansion chamber, and the length and efficiency of a stretched muffler. If you’re tired of your performance engine not getting the power you want, the BBR Tuning High-Performance F2 Thrust Exhaust Muffler is exactly what you need. Specifications: 29in. from exhaust tip through the mount (including bend at the mount) 40mm Mounting Stud Spacing Color: Chrome and black Compatible with 66/80cc 2-stroke bicycle engine kits (can work with 48cc 2-stroke mufflers with 40mm exhaust stud ports) Package Includes: 1x Chrome the BBR Tuning High-Performance F2 Thrust Exhaust Muffler 40mm Muffler Gasket Mounting brackets and hardware Note: This muffler will raise slightly upward and over the magneto/drive sprocket side cases, going to the back of your bicycle. Though it will hug the engine tight, please use caution when riding as to not rest your leg against the muffler after each ride.
RST Replacement Spring Fork 26
$109.99
Basic replacement fork for cross country mountain bikes or an excellent choice for gas bike kits. Mount rim brakes or upgrade to disc brakes. Other sizes, colors, and options are available. Coil spring / rebound adjustment Alloy lower legs and crown Steel steerer tube 2060g Type: Suspension Size: 26" Steerer Type: Threadless Steerer Size: 1-1/8" Steerer Length: 260mm Brake Mount: Post Disc/V-Brake Color: Black Rake: 30mm Race Diameter: 30mm Axle: QR9 Travel: 80mm
Wheel Master Motorbike Mag Wheels - Gas Bike Wheel Set
$199.99
Tired of truing your motorized bike wheels every fifty miles or so? Let’s face it, even the heaviest-duty spoked wheels still need plenty of maintenance and eventually need to be rebuilt. But with the Wheel Master 26 Inch Heavy Duty Motorized Bike Mag Wheel Set you’ll be able to ride longer and faster with more security than regular bike wheels ever gave you. These alloy wheels are meant for heavy riding. Made of heavy duty alloy metal, there are no spokes to worry about other than the 6 big fins that cut through wind a WHOLE lot better than spoked wheels. Unlike standard bike wheel hubs with multiple pieces, these hubs consist of a set of bearings and a thick, sealed alloy center. Most wheels give out easily because of the multiple pieces that combine to make the hub, but because these wheels have no spokes and a solid hub, there’s no need to rebuild your wheels after long rides at high speeds. Each wheel is disc brake-ready, with 6x stud ports to support nearly any disc brake assembly- even the rear wheel. And did we mention that each rear wheel comes with a 44 tooth motorized drive sprocket? Yup, and it’s disc brake ready, too. That means you don’t have to use those old, ratty rag joints to mount your rear sprocket, nor do you have to spend +$90 on a sprocket adapter and the compatible sprocket. All you need is the engine chain and your motorized wheels are almost complete. Of course, any tough wheel needs a strong tire. These single-walled wheels have tire lips big enough to fit fat, knobby 26” tires with lots of grip and tubes that hold lots of air. As far as installation, it couldn’t be any easier: If you’re using disc brakes, install the disc of your disc brake assembly on to the studs of the wheel and fasten them out (if you’re using caliper brakes, just tighten down the disc brake studs on the rear wheel to fasten the rear sprocket to the wheel) Install a single-speed freewheel on to the rear wheel and lock it on to the wheel Line your wheel with tire liner, then install your tubes and tires as you would normally Take one nut and one spacer off of each wheel axle and insert the axle through the wheel’s bearings (leaving a spacer and nut on the other side) Once through, reinstall the spacer on to the open side of the wheel Install the wheels on to your bike, fasten down the remaining nuts on their axles, and align your chain Now you’re ready to ride! So when you’re ready to make your motorized bike a mad man on the tracks as well as the trails, step up to the BBR Tuning 26 Inch Heavy Duty Motorized Bike Mag Wheel Set and feel what you’ve been missing. Specifications Alloy mag wheels with a flip flop style hub with fixed 44T cog for gas powered bicycles Suitable for tires between 1.75 and 2.2 inches wide Multi-speed or single speed freewheel compatible Machined brake track Inner rim width: 17mm Outer rim width: 27mm Axle length front: 155mm Axle length rear: 180mm with Schrader valves Brake Compatibility: Disc Brake and Caliper Brake Bicycle Engine Sprocket Size: 44 Tooth
Flying Horse 2-stroke Gas Bike Kit
$295.00
The Angle Fire 2-Stroke Bicycle Engine Kit is here for any rider looking to strap a motor on their beach cruiser, mountain bike, or road bike and turn it into the street-legal ride of your dreams. No more pedaling up steep hills or charging a battery only for it to die halfway through your commute. With the (engine) you’ll get to where you need to go and back with ease. (All specifications are subject to change - open your kit to verify contents.) Not only do these engines still get you up to 25-35 mph and up to 150 MPG fuel economy, they also come with the 66/80cc High Performance Carburetor to give it that extra boost of power and speed. Of course, no motor would be useful without a balanced crank and upgraded crank bearings. This motor boasts superior crank components and balance over other engines on the market, and this clutch will make sure your motor engages and disengages smoothly. With its all-terrain rear drive sprocket, you better believe this engine kit was meant for anyone looking to use their motor as their main mode of transportation. Product Dimensions and Specifications 2.5 HP (horse power) 25 to 40 mph depending on the gear ratio and weight Fuel Economy: 100-150 miles per gallon The Flying Horse 66/80cc bicycle engine measures about 8.5in.x 7in.x 5in. (HxLxW). These engine fit standard men’s bicycle frames with tubing of 25mm to 29mm in diameter, and around 10in. of clearance from the cranks to the top to be of the frame. Larger frames may require modification to the frame in order to fit an engine. The engine chain does not interfere with your current drive chain and peddling because it rides on the opposite side of the bike sprocket. Product Requirements Installation is a breeze! The rider only needs some basic hardware skills, tools, and around 2-3 hours for installation and fine tuning adjustments (Note: Seller is not responsible for misuse or this kit or any warranty after installation). Fits Most 26" Wheeled Bikes (Mountain, Cruiser, Chopper, Road) with V-frame. The frame should have 9-11” of clearance between the bottom bracket and top bar, and the diameter of the frame tubes should be 25-29mm (around an 1”). Package includes Silver Flying Horse 66/80cc E.P.A. Approved 2-Stroke Engine UPGRADED High Performance Profile Carburetor UPGRADED Exhaust Muffler w/ Catalytic Converter Complete Clutch Cable Assembly with Clutch Wire Clip Drive Chain Idler Pulley Top Quality Japanese 202 Main Bearings 415 Bike Engine Drive Chain Drive Chain Guard 2-Stroke Spark Plug Electron Ignition Coil (CDI) Locking Alloy Clutch Lever Upgraded Twist Throttle and Cable With Grip Updated 1.5L Black Teardrop Gas Tank (approx. ? of a gallon) Fuel Line Throttle Cable Gasoline Tank Switch Sprocket Clamp Assembly 44 Tooth Chrome Drive Sprocket with 9 Holes Large Spring (Heat Shield Spring) Extension Spring (Recoil Spring) High Quality Japanese Bearings on Both Ends of Crank Required Hardware and Gaskets Magneto Kill Switch Bonus: Spark Plug Removal Tool (While Supplies Last)! Bonus: Standard Universal Mounting Bracket Disclaimer: Operating this motorized bicycle and bicycle engine kit involved some risk of serious bodily injury. Buyer accepts responsibility for any and all vehicle operation that may lead to personal injury, economic loss, social distress, other losses, costs and damages. Seller is not responsible for injuries and/or damages resulting from operating this motorized bicycle or bicycle engine kit. Upon purchase, the buyer agrees to comply with local requirements and restrictions in areas where EPA approved engines are allowed on public roadways. Otherwise, the riders agrees to use products for racing (closed-course competition) only and not for on/off public roads. Disclosure of accurate engine size: While we have chosen to use the long standing factory branding engine size of "80cc", the true displacement of the bicycle engine is 66cc. Down through the years China bicycle engine manufactures have advertised their biggest engine as 80cc, therefore we have listed them in the same way on our website. However, the bore and stroke of an 80cc being 47x38mm equals 66cc. Therefore the true displacement of the 80cc bike motor is 66cc. In the west, the volume of a cylinder is calculated by using the formula Volume = Pi x Radius Squared x Stroke. However,in the east the displacement of an engine includes the area of the cylinder head's combustion chamber as well as the volume of the cylinder. Therein lies a discrepancy between measuring standards by the manufactures in China with those in the United States. However, all "80cc" engine kits on the market today are actually 66cc in displacement size if measuring by US standards.
Flying Horse 4-Stroke Gas Bike Kit
$499.99
Ready for a ride that will last? If you’re looking for a tough, reliable, long-lasting bicycle engine kit look no further than our BBR Tuning 5G 4 stroke engine! The all new BBR Tuning 5G 4 stroke bike engine kit features a centrifugal clutch and pull start enhancements, with all of the latest features and upgraded components BBR Tuning has to offer. This 4 stroke bike engine kit is truly the cream of the bike kit crop. Forget premixing oil and fuel! Instead, this engine features an independent oil reservoir which keeps the engine well lubricated. This is the reason the 4 stroke engines are known for their reliability and long life. Moreover, with the centrifugal clutch feature, there is no need to engage and disengage the engine manually. Similar to an engine for a scooter or goped, you simply pull the starter chord and hit the throttle to go! When the bike is stopped, the engine will automatically disengage so that the engine will stay running. This kit is perfect for those that are looking for the added reliability and ease of use of a 4 stroke engine with an automatic transmission. (Specifications vary, open your kit to verify contents.) This kit comes with all the components you'll need to convert a compatible bicycle into a motorized bicycle. Startup is a breeze and you can stop the engine with a simple killswitch provided with the throttle assembly. Don't be fooled by other retailers, selling outdated, non-EPA approved, old generation bicycle engine kits! All of the Flying Horse engines feature the latest updates, including high quality needle bearings and Japanese ball bearings. Older generation engines use cheap bushings that do not last! BikeBerry.com takes extra measures to ensure our manufactures abide by strict quality control assurance measures and use the highest quality material so that we can make certain that all of our customers get only the best! ** Please note: Sprocket Clamp Assemblies included with BBR Tuning 2-Stroke 48cc and 66/80cc, and 4-Stroke 49cc bike engine kits come with only 1x set of metal plates. Older production of these assemblies included 2x sets, but from testing and redesigning, existing engine kits and engine kits in the future will only require 1x set. This redesigned assembly helps secure your rear wheel sprocket better than in previous production. NOTE: Wide Crank Assembly are only Compatible with 9/6th inch pedals. Will not be compatible with Micargi Beach Cruiser's stock pedals. For installing this kit buyer may need some basic hardware skills, tools, and take around 2-3 hours to install and do some adjustments. Seller is not responsible for misuse or this kit or any warranty after installation. This is a do-it-yourself kit and being such all repairs, maintenance and modifications are the responsibility of the buyer. Bicycle engine kit fits most 26" Wheel Bikes (Mountain, Cruiser, Chopper, Road) with V-frame. Please check to see if your bike is compatible. Product Dimensions and Specifications 48cc engine kit is about 9" height 9.5" length 7" width. The bicycle gas engine kit includes a mounting plate that fits on standard 25mm to 29mm frame tube. Larger frame size requires modification to the mounting plate and/or frame of your bicycle. 2-3 HP (horsepower) 20 to 25 mph depending on the gear ratio and weight. Fuel Economy: MPG 100-150 miles per gallon Oil Capacity: 250 mL (~8.45 oz) Independent drive sprocket and chain does not interfere with your current drive chain and peddling can be restored with a wide crank assembly. Package Includes *(Products pictured may come in different colors but does not hinder performance.) 1. 5G 4-Stroke Centrifugal Transfer Case (6:1 Gear Ratio) 2. HuaSheng 49cc Pull Start Bicycle Engine 3. High Performance Low Profile Carburetor 4. Upgraded Hush Muffler 5. High Quality Japanese Main Bearings 6. Heavy Duty 415 Bike Chain 7. Upgraded Chain Tension Guide 8. Chain Guard 9. Spark Plug 10. CDI (Ignition Coil) 11. Upgraded Twist Throttle and cable with matching grip 12. Engine Mounting Plate 13. Black Teardrop Gas Tank (1.5L) 14. Fuel Line 15. Throttle Cable 16. Gasoline Tank Switch 17. Sprocket Clamp Assembly 18. High Quality Needle Bearings on Both Ends Crank 19. 44 Tooth Chrome Sprocket with 9 Holes 20. Magneto 21. Kill Switch 22. Required Hardware and Gaskets 23. Bonus: Spark Plug Removal Too! 24. Bonus: Wide crank set with accompanying bottom bracket! Disclaimer: Operating a bike, motorized bicycle or bike with a bicycle engine kit installed involved some risk of serious bodily injury. Buyer accepts responsibility for any and all vehicle operations that may lead to personal injury, economic loss, social distress, other losses, costs and damages. Seller is not responsible for injuries and/or damages resulting from operating this motorized bicycle or bicycle engine kit. Seller is not responsible for misuse
Micargi Cruiser Gas Bike Conversion 4 Stroke 48cc Gas Bike
$999.99
26 x 2.125 Tires Single Speed Coaster Brake Fenders 48cc 4 Stroke Motor Automatic Clutch Pull Start 2.4L Gas Tank 100mpg Notice and Disclaimer on Gas Bikes All gas bikes shown are assembled from kits. All guarantees are solely from manufacturer. All gas bikes are sold as-is. These kits are not approved for use on public highways, but may be permitted along the side of the road. Always follow all laws of operation for the jurisdiction you are riding. Gas Bikes are not titled and are unregistered and are not motorized vehicles. Gas bike kits and conversions are essentially toys (your hobby). Customer accepts all risks of use. Operating a bike, motorized bicycle or bike with a bicycle engine installed involves some risk of serious bodily injury. Buyer accepts responsibility for any and all vehicle operation that may lead to personal injury, economic loss, social distress, other losses, costs and damages. Seller is not responsible for injuries and/or damages resulting from operating this motorized bicycle or bicycle engine. Seller is not responsible for misuse of this or any warranty. Not all motorized bicycles are allowed for operation on roads, bike lanes or the side of the road. We make no guarantee as to the road legality of these bikes. See our terms and conditions on your sales invoice. Our gasoline operated products are NOT compliant with Environmental Protection Agency ( E.P.A. ) or California Air Resources Board (C.A.R.B) for the use on/off Public roads. Upon purchase, the buyer agrees to use products for racing (closed-course competition) only. Check your bike for safety before every ride. Wear a helmet. Pedal when starting out to save wear on the clutch. Other gas bike models are available. Delivery and shipping options.
PhatMoto Rover 4-stroke 79cc Gas Bike
$1,199.99 - $1,499.99 $1,499.99 20% Off
Fully assembled and ready to ride. Custom build Gasbike 79cc 4-stroke. All new frame and engine from kit. This bike is 100% purpose-built for this engine. It's an amazing ride. Features: 3.0 HP 79cc Industrial Grade OHV Single Cylinder 4-Stroke Fuel Tank Capacity 3/4 Gallon, 2.85 L Automatic clutch Uses Regular grade gas Lightweight Aluminum Frame 26" HD 12 gauge spoke wheels w/26X2.35 easy riding, long lasting, high-volume tires Suspension Forks Front Mechanical Disc Brake and Rear V-Brake The Phatmoto Rover is the affordable all-in-one motorized bicycle that eliminates the complexities with engine conversion kits. Our pre-built, custom designed gas bike, can be pedal or engine powered and travels up to 100 miles, at speeds of 25 MPH, on less than 1 gallon of gas. Far from your standard motorized gas-hybrid bike, Phatmoto hides quite a bit of convenient engineering features within traditional bike frame appearance. Pedal, Gas Motor, or Hybrid Power. Unlike many DIY conversion kits or electric bikes, Phatmoto was specifically engineered as a dual purpose gas-hybrid bike that makes it significantly easier to ride when pedaling alone and doesn't restrict the engine when under gas power. It comes built on a custom Engineered Bike Frame. Unlike many DIY gas bike conversion kits, Phatmoto's bicycle frame is engineered from the ground up to discreetly hide its fuel tank internally, securely bolts its motor to built-in frame mount, and safely encases the drivetrain. Easy Pull-Start Handle Engine: Unlike most DIY gas bike conversion kits using two-stroke engines that require vigorous pedaling turn on, Phatmoto opted for a four-stroke engine with a simple pull-start handle and on/off switch for quick and effortless riding. Notice and Disclaimer on Gas Bikes All gas bikes shown are assembled from kits. All guarantees are solely from manufacturer. All gas bikes are sold as-is. These kits are not approved for use on public highways, but may be permitted along the side of the road. Always follow all laws of operation for the jurisdiction you are riding. Gas Bikes are not titled and are unregistered and are not motorized vehicles. Gas bike kits and conversions are essentially toys (your hobby). Customer accepts all risks of use. Operating a bike, motorized bicycle or bike with a bicycle engine installed involves some risk of serious bodily injury. Buyer accepts responsibility for any and all vehicle operation that may lead to personal injury, economic loss, social distress, other losses, costs and damages. Seller is not responsible for injuries and/or damages resulting from operating this motorized bicycle or bicycle engine. Seller is not responsible for misuse of this or any warranty. Not all motorized bicycles are allowed for operation on roads, bike lanes or the side of the road. We make no guarantee as to the road legality of these bikes. See our terms and conditions on your sales invoice. Our gasoline operated products are NOT compliant with Environmental Protection Agency ( E.P.A. ) or California Air Resources Board (C.A.R.B) for the use on/off Public roads. Upon purchase, the buyer agrees to use products for racing (closed-course competition) only. Check your bike for safety before every ride. Wear a helmet. Pedal when starting out to save wear on the clutch. Other gas bike models are available. Delivery and shipping options.
Umoto Ghost Racer 49cc Gas Bike
$1,299.99
4-stroke-$1299.99 (Specific parts may vary - ask about the one you want for customization) Deluxe Gas bike, all aluminum, lightweight frame, w/built in 3.4l gas tank 26" heavy duty mag wheels Med-Lg frame suitable for 5'5" to 6'3" Single speed pedaling Heavy duty highway tires 49cc Ghost Racer 4-stroke motor w/auto clutch, belt drive transmission Sturdy MTB-style fork Front disc brake, caliper rear brake Notice and Disclaimer on Gas Bikes All gas bikes shown are assembled from kits. All guarantees are solely from manufacturer. All gas bikes are sold as-is. These kits are not approved for use on public highways, but may be permitted along the side of the road. Always follow all laws of operation for the jurisdiction you are riding. Gas Bikes are not titled and are unregistered and are not motorized vehicles. Gas bike kits and conversions are essentially toys (your hobby). Customer accepts all risks of use. Operating a bike, motorized bicycle or bike with a bicycle engine installed involves some risk of serious bodily injury. Buyer accepts responsibility for any and all vehicle operation that may lead to personal injury, economic loss, social distress, other losses, costs and damages. Seller is not responsible for injuries and/or damages resulting from operating this motorized bicycle or bicycle engine. Seller is not responsible for misuse of this or any warranty. Not all motorized bicycles are allowed for operation on roads, bike lanes or the side of the road. We make no guarantee as to the road legality of these bikes. See our terms and conditions on your sales invoice. Our gasoline operated products are NOT compliant with Environmental Protection Agency ( E.P.A. ) or California Air Resources Board (C.A.R.B) for the use on/off Public roads. Upon purchase, the buyer agrees to use products for racing (closed-course competition) only. Check your bike for safety before every ride. Wear a helmet. Pedal when starting out to save wear on the clutch. Other gas bike models are available. Delivery and shipping options.
Sun Bicycles Atlas Gas Powered Trike Conversion
$1,499.99
This trike can be built to order. The standard configuration price is $1,549.99. Many options are available. Trike Specs: Heavy duty high-tensile steel Low-Step frame Single-speed drivetrain (Additional gearing options available separately) Alloy linear-pull front hand brake and rear band brake with parking locks (Additional brake options available separately) 3-piece steel crankset with sealed cartridge bottom bracket Heavy duty steel rims with 12g stainless steel spokes 24" x 2.125" heavy duty knobby tires 9" hi-rise steel handlebar and stem with rubber grips Heavy duty coil spring saddle with steel base Steel chain guard and nickel plated front fender Heavy duty steel cargo deck with viny top 500 Pound Limit (250 Rider & 250 Cargo) Use caution when cornering - this is a trike - slow down to no more than 5mph when turning for safety Engine Specs: 3 HP (78.5cc - 79cc) OHV GasBike Horizontal Shaft Gas Engine Brand GasBike Engines (Huasheng) Engine displacement (cc) 79cc Horsepower (hp) 3 Maximum speed (rpm) 3600 RPM Maximum Torque (ft. - lbs.) 3.5 ft. lbs. @ 2500 RPM Mounting pattern 102mm L x 104mm W - 61.5mm W (4 in. L x 4.9 in. W - 2.4 in. W ) Mounting type Horizontal Shaft rotation direction Counter clockwise Sound rating (dB) 104 dB Start type Recoil start Notice and Disclaimer on Gas Bikes All gas bikes shown are assembled from kits. All guarantees are solely from manufacturer. All gas bikes are sold as-is. These kits are not approved for use on public highways, but may be permitted along the side of the road. Always follow all laws of operation for the jurisdiction you are riding. Gas Bikes are not titled and are unregistered and are not motorized vehicles. Gas bike kits and conversions are essentially toys (your hobby). Customer accepts all risks of use. Operating a bike, motorized bicycle or bike with a bicycle engine installed involves some risk of serious bodily injury. Buyer accepts responsibility for any and all vehicle operation that may lead to personal injury, economic loss, social distress, other losses, costs and damages. Seller is not responsible for injuries and/or damages resulting from operating this motorized bicycle or bicycle engine. Seller is not responsible for misuse of this or any warranty. Not all motorized bicycles are allowed for operation on roads, bike lanes or the side of the road. We make no guarantee as to the road legality of these bikes. See our terms and conditions on your sales invoice. Our gasoline operated products are NOT compliant with Environmental Protection Agency ( E.P.A. ) or California Air Resources Board (C.A.R.B) for the use on/off Public roads. Upon purchase, the buyer agrees to use products for racing (closed-course competition) only. Check your bike for safety before every ride. Wear a helmet. Pedal when starting out to save wear on the clutch. Other gas bike models are available. Delivery and shipping options. ________________________________________________________
Page 1 of 1
Subscribe